Lab Four –Audio Amplifiers
ECT246 Electronic Systems III with Lab
Part A: Audio Amps
Given an audio amplifier application that uses an integrated amplifier, examine the overall amplifier’s performance and verify the operation by using suitable input and output circuits.
Investigation of the LM386 Audio Amplifier takes place during week 4. The LM386 is a versatile special purpose op-amp used to amplifier audio frequencies. The device is contained in a single 8-pin dip package and has a gain of up to 200 and a power output of 1-watt.
A. Use an Internet search utility, such as Google, find an audio amplifier such as a LM386 download the specification sheet and determine its general characteristics such as its general description, the package type and pin configuration.
b. From the data sheet find the following information and record.
What are its general characteristics?
B. Use the specification sheet to determine its electrical characteristics and operating values.
a. Record the electrical values of the LM386.
Absolute Maximum Ratings:
Operating supply voltage
C. Using information from the data sheet or other sources and an application such as Multisim, Visio, or a CAD program draw the schematic and verify the component values of an audio amplifier application using the device.
a. Using the Typical Applications section or other source find an amplifier with a gain equal to 20.
b. Use an application such as Multisim, Visio, or a CAD program to create the circuit schematic. Label the schematic, LM386 Audio Amplifier.
c. Label the pin numbers on the LM386 and give each component a name and value.
d. Explain briefly how the gain of the LM386 can be changed.
D. Construct the audio amplifier on your breadboardwith various gains (20 and 200). Using a frequency generator as an input, verify the amplification of the audio amplifier. Use 10mV peak as the input signal and keeping all the component connecting wired as short as possible. Also keep all the components close together on the breadboard.
a. For measurements purposes, prototype an amplifier similar to the one below. Remember keep all component connecting wires as short as possible, and keep all components as close to the audio amplifier as possible. The 10mV peak input is set between the 1k resistor and C6.
b. Complete the tablebelow.
R C5 Expected Measured
— — _____ _____ _____ _____
_____ _____ _____ _____
— _____ _____ _____ _____
c. Beginning with pin 1 an 8 open and the frequency generator set to 10mVpat 1 kHz, use the oscilloscope to measure the voltage values. Calculate the gain of the amplifier, . Record the results on the sheet.
d. Continue this procedure until you have determined the three gain values.
e. Were there any problems with the different gain values? If so, explain the symptoms and how to correct the problem.
E. Determine and plot the audio amplifier’s frequency response. Determine midband gain, 3-dB bandwidth, critical frequencies and roll-off rate. Compare the results to the data sheet.
a. Using the information above, set the gain of the amplifier to 20.
b. Set the output of the frequency generator to a sine wave with amplitude of 100 mV at 1 (one) Hz.
c. Complete the table below.
f (Hz) Gain
1 _____ _____ _____
10 _____ _____ _____
100 _____ _____ _____
1k _____ _____ _____
10k _____ _____ _____
100k _____ _____ _____
500k _____ _____ _____
d. With the frequency set to 1 Hz, use the oscilloscope to measure the above values and calculate the gain. Note that very low or high frequencies may be difficult to measure.
e. Continue changing the input frequency by a power of 10 (10, 100, etc.) until you reach 500kHz.
f. Use a piece of graph paper to plot the results. A work sheet can be found in Doc Sharing, week 4 — “graph_paper.doc”.
F. Connect an input circuit such as a frequency generator and a microphone and a load such as a speaker verify the operation and troubleshoot any problems.
a. Prototype the advance amplifier circuit for this step. Set the gain to 20.
b. Connect a frequency generator set to a sine wave at 400 mV peak and 100 Hz to the input of the circuit. Connect an 8-ohm speaker to the output of the circuit. Set to ithighest value.
c. Write down your observations.Record the information below.
d. Apply power and record what you hear. Slowly decrease and record any changes. Continue to decrease. Use an oscilloscope to observe the output signal. What is happening to the output waveform?
e. Change the input frequency to 1 k Hz and 10 kHz and record the change.
f. Change the frequency generator to a square wave and repeat the steps above. Record the results.
g. Remove the frequency generator and connect a dynamic microphone to the input. Test the circuit and record the results. Vary for maximum output. Can you get maximum gain from the circuit without oscillation?
Part B – More LM386
1. The LM386 may be used to amplify voice inputs. Dynamic or Condenser (Electret) microphone are two common input devices. Dynamic microphones can be connected directly to the input of the LM386 amplifier and uses resistance variation within the microphone to convert voice fluctuations into small electrical signals. The condenser type microphone use capacitance to detect these changes and requires a bias voltage applied to the microphone.
The specifications of a typical condenser microphone are shown below.
2 to 10V DC
1K ohm impedance
50 to 8 KHz
Using the information above, create a bias circuit for the microphone. Draw the schematic and label each component.
1 56mV 320mV 5.71 15.1
10 64mV 320mV 5 14
100 112mV 1.28V 11.42 21.15
1k 112mV 1.28V 11.42 21.15
10k 160mV 1.20V 7.5 17.5
100k 3 9.54
After plotting the graph we need to go below 100 hz and read the frequency that the gain is 8.1. This is f1
Then go above 1k until the gain is 8.1 and read that frequency. This is f2
This is semi log paper, note the bottom horizontal scale is frequency, and always gets 10 times larger on the next decade. There are no zeros on the graph. 10^0 = 1 so that is the first number, 10^1 = 10 so we jump from counting 1’s to counting 10’s, for example 1,2,3,4,5,6,7,8,9,10, 20,30 etc.
The vertical scale is gain in decibels and uses a linear scale.
The point plotted is a frequency of 10 hertz and a gain of 7 db.
Delivering a high-quality product at a reasonable price is not enough anymore.
That’s why we have developed 5 beneficial guarantees that will make your experience with our service enjoyable, easy, and safe.
You have to be 100% sure of the quality of your product to give a money-back guarantee. This describes us perfectly. Make sure that this guarantee is totally transparent.Read more
Each paper is composed from scratch, according to your instructions. It is then checked by our plagiarism-detection software. There is no gap where plagiarism could squeeze in.Read more
Thanks to our free revisions, there is no way for you to be unsatisfied. We will work on your paper until you are completely happy with the result.Read more
Your email is safe, as we store it according to international data protection rules. Your bank details are secure, as we use only reliable payment systems.Read more
By sending us your money, you buy the service we provide. Check out our terms and conditions if you prefer business talks to be laid out in official language.Read more